:: CommandLine IT Solutions :: Telefonia IP - Asterisk ::

From 2 to 24 ports are supported. Mix TE and NT modes, as required. Changing modes requires no jumpers - simply invert the colour-coded module. Supports Asterisk®, Yate™,   FreeSwitch™,   CallWeaver™, PBX/IVR projects, as well as other Open Source and proprietary PBX, Switch, IVR or VoIP gateway applications. Single synchronous PCI and PCI Express interface for all 24 BRI interfaces. Six ports per RemoraTM card. Dimensions: 2U Form factor: 187mm x 55mm for use in restricted chassis. Short 2U compatible mounting clips included for installation in 2U rackmount servers and high quality, tested 2m 8-pin RJ45 port splitter cables included. 32 bit bus master DMA data exchanges across PCI interface at 132 Mbytes/sec for minimum host processor intervention. Autosense compatibility with 5 V and 3.3 V PCI busses. Fully PCI 2.2 and PCI Express compliant, compatible with all commercially available motherboards, proper sharing of PCI interrupts. Intelligent hardware: Downloadable FPGA programming with multiple operating modes. Add new features related to voice and/or data when they become available. Power: 800mA peak, operational 300mA max at +3.3 V or 5 V. Temperature range: 0 - 50°C. Optimized DMA stream and hardware-level HDLC handling unload the host CPU. Raw bitstream interfaces can be used to support arbitrary non-standard line protocols, such as non-byte aligned monosynch or bisynch. WANPIPE® supports certified, field tested, and reliable Frame Relay, PPP, HDLC and X.25. The Sangoma A500 S/T BRI Interface Card delivers superior audio quality and scalability. Expand from two to twenty-four ports of BRI with optional Octasic™ Telco-grade, hardware echo cancellation. A single PCI or PCI Express slot hosts the connection for up to 24 ports and ensures common synchronous clocking for all channels with no signaling issues. The card is 100% software configurable. Finally, a BRI card that upholds Sangoma's high standards of quality in engineering and untiring product support.

Eight T1/E1 ports with a single PCI interface for high performance voice and data applications. TDM clocking mode: Network timing can be passed from a network - connected DS0 to any or all of the other ports. Both T1 and E1 are supported simultaneously, making it possible to mix T1 channel banks and E1 networks with full channel synchronization. Line decoding: HDB3, AMI, B8ZS. Framing: CRC4, non-CRC4, ESF, D4T1/E1. Support for the Asterisk™, OPAL™ Yate, FreeSwitch™ PBX/IVR projects, as well as other Open Source and proprietary PBX/Switch/IVR/VoIP gateway applications. All Sangoma's AFT products, including the A108 card use the same base PCI interface card, and the same professionally engineered firmware on the same family of Field Programmable Gate Arrays. A108, A108D PCI: Fully PCI 2.2 compliant, compatible with all commercially available motherboards, proper interrupt sharing without manual tuning. A108E, A108DE PCI Express: 1 Lane PCI Express bus. Dimensions: 2U Form factor: 120mm x 55 mm for use in restricted chassis. Short 2U compatible mounting clips included for installation in 2U rackmount servers. High quality, tested RJ45 cables included. Power: 800mA peak, operational 300mA max at +3.3v or 5v.Temperature range: 0-50C. Autosense compatibility with 5v and 3.3v PCI busses. Intelligent hardware: Downloadable Field Programmable Gate Array programming with multiple operating modes. Field upgradeable so that new features related to voice and/or data can be added when they become available. 32 bit bus master DMA data exchanges across PCI interface at 132Mbytes/sec for minimum host processor intervention. Ring buffer DMA handling for minimum host intervention and guaranteed data integrity on high volume systems. Supports Robbed Bit Channel Associated Signaling (CAS) and ISDN PRI. T1/E1 and fractional T1/E1, multiple channel HDLC per line for mixed data/TDM voice applications. Optimized per channel DMA streams and hardware-level HDLC handling unload the host CPU. EDAC™ (patent pending) technology will be integrated to drastically reduce the cost of echo cancellation. Field upgradeable hardware allows for new TDM-related functions to be added as they become available. Raw bitstream interfaces can be used to support arbitrary non-standard line protocols such as non-byte aligned monosynch or bisynch. WAN data connection is supported by Sangoma's standard WANPIPE® routing stack, and is completely independent of TDM voice application for total system reliability. WANPIPE® supports certified, field tested and reliable Frame Relay, PPP, HDLC and X.25. A108D Inetrface: PCI Digital Signal Processor: Hardware echo canceller A108E Inetrface: PCI Express Digital Signal Processor: N/A A108DE Inetrface: PCI Express Digital Signal Processor: Hardware echo canceller Obtainable in both PCI (A108) and PCI Express (A108E) form factors, the A108 provides up to 16.4Mbps of full duplex data throughput or 240 voice calls over eight T1 and or E1 lines to support high performance PCI-based routing and telephony systems. Advanced clocking features allow E1 and T1 lines to be mixed with full synchronization. As part of Sangoma's AFT range of products, the A108 makes use of the same high performance PCI interface that has been deployed in large quantities all over the world. The available A108D and A108DE cards include Octasic ®'s DSP hardware and certified algorithms providing carrier-grade echo cancellation and Voice Quality Enhancement (VQE) functions.

Four T1/E1 ports with a single PCI or PCI-Express interface optimized for high performance voice and data applications. Mix T1 channel banks and E1 networks with full channel synchronization. TDM clocking mode lets network timing to be passed from a network- connected DS0 to any or all of the other ports, so both T1 and E1 are supported simultaneously. Support for Asterisk®, Yate™, CallWeaver™ and FreeSwitch™ PBX/IVR Projects, as well as other open source and proprietary PBX, Switch, IVR, or VoIP gateway applications. All of Sangoma’s AFT products use the same base PCI interface card. Fully compatible with all commercially available motherboards - proper PCI-standard interrupt sharing without manual tuning. Dimensions: 2U Form factor: 120 mm x 55 mm for use in restricted chassis. Includes high-quality, tested RJ45 cables and short 2U mounting clips for installation in 2U rack-mount servers. Intelligent hardware: Downloadable FPGA programming with multiple operating modes. Add new features related to voice and/or data when they become available. Autosense compatibility with 5V and 3.3V PCI busses. Line decoding: HDB3, AMI, B8ZS. Framing: CRC-4, Non CRC4, ESF, SF, D4T1/E1. Also compatible with Japan’s J1. A104E and A104DE PCI Express: 1 Lane PCI Express bus. Power: 800 mA peak, operational 300 mA max at +3.3 V or 5 V. Temperature range: 0 - 50 °C. 32-bit bus master DMA data exchanges across PCI interface at 132 Mbytes/sec for minimum host processor intervention. Ring buffer DMA handling for minimum host intervention and guaranteed data integrity on high volume systems. Supports Robbed Bit Channel Associated Signaling (CAS) and ISDN PRI. T1/E1 and fractional T1/E1, multiple channel HDLC per line for mixed data/TDM voice applications. Optimized per channel DMA streams and hardware-level HDLC handling unload the host CPU. Uses raw bitstream interfaces to support arbitrary non-standard line protocols, such as non-byte aligned monosynch or bisynch. WANPIPE® routing stack is completely independent of TDM voice application for total system reliability. WANPIPE® supports certified, field-tested, and reliable Frame Relay, PPP, HDLC, and X.25. A104D Inetrface: PCI Digital Signal Processor: Hardware echo canceller A104E Inetrface: PCI Express Digital Signal Processor: N/A A104DE Inetrface: PCI Express Digital Signal Processor: Hardware echo canceller Part of Sangoma's award-winning Advanced Flexible Telecommunications product line, the A104 uses the same high- performance PCI or PCI Express interface that is providing superior performance in critical systems all over the world. The A104 supports up to 120 voice calls or 8.192 Mbps of full- duplex data throughput over four T1, E1, or J1 lines. Take advantage of hardware and software improvements, as soon as they become available. Like all cards in Sangoma's AFT family, the A104 is field upgradable with crash-proof firmware.

Two T1/E1 ports with a single PCI or PCI-Express interface optimized for high performance voice and data applications Mix T1 channel banks and E1 networks with full channel synchronization. TDM clocking mode lets network timing to be passed from a network- connected DS0 to any or all of the other ports, so both T1 and E1 are supported simultaneously. Support for Asterisk®, Yate™, CallWeaver™ and FreeSwitch™ PBX/IVR Projects, as well as other open source and proprietary PBX, Switch, IVR, or VoIP gateway applications. All of Sangoma’s AFT products use the same base PCI interface card. Fully compatible with all commercially available motherboards - proper PCI- standard interrupt sharing without manual tuning. Dimensions: 2U Form factor: 120 mm x 55 mm for use in restricted chassis. Includes high-quality, tested RJ45 cables and short 2U mounting clips for installation in 2U rack-mount servers. Intelligent hardware: Downloadable FPGA programming with multiple operating modes. Add new features related to voice and/or data when they become available. Autosense compatibility with 5V and 3.3V PCI busses. Line decoding: HDB3, AMI, B8ZS. Framing: CRC-4, Non CRC4, ESF, SF, D4T1/E1. Also compatible with Japan’s J1. A102E and A102DE PCI Express: 1 Lane PCI Express bus. Power: 800 mA peak, operational 300 mA max at +3.3 V or 5 V. Temperature range: 0 - 50 °C. 32-bit bus master DMA data exchanges across PCI interface at 132 Mbytes/sec for minimum host processor intervention. Ring buffer DMA handling for minimum host intervention and guaranteed data integrity on high volume systems. Supports Robbed Bit Channel Associated Signaling (CAS) and ISDN PRI. T1/E1 and fractional T1/E1, multiple channel HDLC per line for mixed data/TDM voice applications. Optimized per channel DMA streams and hardware-level HDLC handling unload the host CPU. T1/E1 and fractional T1/E1, multiple channel HDLC per line for mixed data/TDM voice applications. Optimized per channel DMA streams and hardware-level HDLC handling unload the host CPU. Uses raw bitstream interfaces to support arbitrary non-standard line protocols, such as non-byte aligned monosynch or bisynch. WANPIPE® routing stack is completely independent of TDM voice application for total system reliability. WANPIPE® supports certified, field-tested, and reliable Frame Relay, PPP, HDLC, and X.25.A102D Interface: PCI Digital Signal Processor: Hardware echo canceller A102E Inetrface: PCI Express Digital Signal Processor: N/A A102DE Inetrface: PCI Express Digital Signal Processor: Hardware echo canceller The A102 uses the same high-performance PCI or PCI Express interface that providing superior performance in critical systems all over the world. The A102 supports up to 60 voice calls or 4.096 Mbps of full- duplex data throughput over two T1, E1, or J1 lines two ports of optimized voice and data over T1, E1, and JI available with Telco-grade hardware echo cancellation.

One T1/E1 port with optimum PCI Express or PCI interface for high performance voice and data applications. Line decoding: HDB3, AMI, B8ZS. Framing: CRC-4, Non CRC4, ESF, SF, D4. Also compatible with Japan’s J1. Support for Asterisk™, Yate™, and FreeSwitch™ PBX/IVR Projects, as well as other open source and proprietary PBX/Switch/IVR/VoIP gateway applications. All of Sangoma’s AFT products use the same base PCI interface card and the same professionally engineered firmware on the same family of Field Upgradeable Gate Arrays. Fully compatible with all commercially available motherboards—proper PCI-standard interrupt sharing without manual tuning. A101E and A101DE PCI Express: 1 Lane PCI Express bus. Dimensions: 2U Form factor: 120 mm x 55 mm for use in restricted chassis. Includes high quality, tested RJ45 cables and short 2U mounting clips for installation in 2U rack mount servers. Power: 800 mA peak, operational 300 mA max at +3.3 V or 5 V. Temperature range: 0 - 50 °C. Autosense compatibility with 5 V and 3.3 V PCI busses. Intelligent hardware: Downloadable FPGA programming with multiple operating modes. Add new features related to voice and/or data when they become available. 32-bit bus master DMA data exchanges across PCI interface at 132 Mbytes/sec for minimum host processor intervention. Ring buffer DMA handling for minimum host intervention and guaranteed data integrity on high volume systems. T1/E1 and fractional T1/E1, multiple channel HDLC per line for mixed data/TDM voice applications. Optimized per channel DMA streams and hardware-level HDLC handling unload the host CPU. Use raw bitstream interfaces to support arbitrary non-standard line protocols, such as non-byte aligned monosynch or bisynch. WANPIPE® routing stack is completely independent of TDM voice application for total system reliability. WANPIPE® supports certified, field-tested, and reliable Frame Relay, PPP, HDLC, and X.25. A101D Interface PCI Digital Signal Processor: Hardware echo canceller A101E Interface PCI Express Digital Signal Processor: N/A A101DE Interface PCI Express Digital Signal Processor: Hardware echo canceller

From 2 to 24 ports supported, mixing FXO and FXS interfaces, as required. Support for the Asterisk™, Yate™, FreeSwitch™, CallWeaver™, OPAL™ PBX/IVR projects, as well as other Open Source and proprietary PBX/Switch/IVR/VoIP gateway applications. Single synchronous PCI interface for all 24 FXO/FXS ports. Four RJ11 ports per Remora™ card. Dimensions: 2U Form factor: 120 mm x 55 mm for use in restricted chassis. Short 2U compatible mounting clips available for installation in 2U rack- mount servers. 32 bit bus master DMA data exchanges across PCI interface at 132Mbytes/sec for minimum host processor intervention. Autosense compatibility with 5 V and 3.3 V PCI busses. Fully PCI 2.2 compliant, compatible with all commercially available motherboards, proper sharing of PCI interrupts. Intelligent hardware: Downloadable Field Programmable Gate Array programming with multiple operating modes. Field upgradeable so that new features can be added when they become available. Power: 800mA peak, operational 300 mA max at +3.3 V or 5 V. Superior audio quality in a card that is expandable from two to twenty-four ports in a half-height form factor the Sangoma A200 FXO/FXS card delivers! A single PCI or PCI Express slot hosts the connection and ensures common synchronous clocking for all channels. Use this card in your PC to accommodate up to twenty-four simultaneous external calls